Здравейте намерих програма , която да ми помага при писането на кода за този контролер.

В клипа https://www.youtube.com/watch?v=2cjufbgOBYo се посочва всичко как се прави,правя го стъпка по стъпка,но след като се опитам да заредя програмата в контролера излиза следната грешка и незнам какво да правя.

Arduino: 1.8.2 (Windows 7), Board: "Arduino/Genuino Uno"

Sketch uses 7152 bytes (22%) of program storage space. Maximum is 32256 bytes.
Global variables use 437 bytes (21%) of dynamic memory, leaving 1611 bytes for local variables. Maximum is 2048 bytes.
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x06
avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x06
avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x66
avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0xe6
avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x80
avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0x98
avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x80
avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x06
avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x06
avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x66
An error occurred while uploading the sketch

This report would have more information with
"Show verbose output during compilation"
option enabled in File -> Preferences.

|||||||||||||||||||||||||||||||||||

||||А това е кода.||||

|||||||||||||||||||||||||||||||||||

/* 
   -- New project -- 
    
   This source code of graphical user interface  
   has been generated automatically by RemoteXY editor. 
   To compile this code using RemoteXY library 2.3.3 or later version  
   download by link http://remotexy.com/en/library/ 
   To connect using RemoteXY mobile app by link http://remotexy.com/en/download/                    
     - for ANDROID 4.1.1 or later version; 
     - for iOS 1.2.1 or later version; 
     
   This source code is free software; you can redistribute it and/or 
   modify it under the terms of the GNU Lesser General Public 
   License as published by the Free Software Foundation; either 
   version 2.1 of the License, or (at your option) any later version.     
*/ 

////////////////////////////////////////////// 
//        RemoteXY include library          // 
////////////////////////////////////////////// 

// RemoteXY select connection mode and include library  
#define REMOTEXY_MODE__ESP8266_HARDSERIAL_POINT

#include <RemoteXY.h> 

// RemoteXY connection settings  
#define REMOTEXY_SERIAL Serial 
#define REMOTEXY_SERIAL_SPEED 115200 
#define REMOTEXY_WIFI_SSID "RemoteXY"  - Тук би трябвало WiFi modue да е с това име, но то НЕ СЕ променя,следователно програмата не се зарежда както трябва.   http://store.picbg.net/pubpic/CF/6F/e12e2cfe5fc0cf6f.png 

#define REMOTEXY_WIFI_PASSWORD "12345678" 
#define REMOTEXY_SERVER_PORT 6377 

// RemoteXY configurate   
#pragma pack(push, 1) 
uint8_t RemoteXY_CONF[] = 
  { 255,2,0,0,0,30,0,8,13,0,
  2,1,73,25,22,11,2,26,31,31,
  79,78,0,79,70,70,0,1,0,11,
  25,12,12,2,31,88,0 }; 
   
// this structure defines all the variables of your control interface  
struct { 

    // input variable
  uint8_t switch_1; // =1 if switch ON and =0 if OFF 
  uint8_t button_1; // =1 if button pressed, else =0 

    // other variable
  uint8_t connect_flag;  // =1 if wire connected, else =0 

} RemoteXY; 
#pragma pack(pop) 

///////////////////////////////////////////// 
//           END RemoteXY include          // 
///////////////////////////////////////////// 

#define PIN_SWITCH_1 12
#define PIN_BUTTON_1 8

void setup()  
{ 
  RemoteXY_Init ();  
   
  pinMode (PIN_SWITCH_1, OUTPUT);
  pinMode (PIN_BUTTON_1, OUTPUT);
   
  // TODO you setup code 
   
} 

void loop()  
{  
  RemoteXY_Handler (); 
   
  digitalWrite(PIN_SWITCH_1, (RemoteXY.switch_1==0)?LOW:HIGH);
  digitalWrite(PIN_BUTTON_1, (RemoteXY.button_1==0)?LOW:HIGH);
   
  // TODO you loop code 
  // use the RemoteXY structure for data transfer 

}

Благодаря!